Розділ 1. Композиційні матеріали на основі полімерів (матеріали, технології, обладнання, вибори)
Постійне посилання зібрання
Переглянути
Перегляд Розділ 1. Композиційні матеріали на основі полімерів (матеріали, технології, обладнання, вибори) за Назва
Зараз показуємо 1 - 20 з 23
Результатів на сторінці
Налаштування сортування
Документ Відкритий доступ Composite of cellulose-nanofiber-reinforced cellulose acetate butyrate: improvement of mechanical strength by cross-linking of hydroxyl groups(Liha-Pres, 2023) Milotskyi, Romain; Serizawa, Ryo; Sharma, Gyanendra; Wada, Naoki; Takahashi, KenjiToday, biocomposites produced from a bio-based filler and bio based matrix are a great attraction, which can present desired functionalities at a reasonable cost. In this study, cellulose laminates were prepared by using CNF as a filler and cellulose acetate butyrate (CAB) as the polymer matrix. Cellulose composite material was manufactured by sandwiching CNF reinforcement filler between CAB matrices using the hot-press technique. The cross-linking agent polyisocyanurate D376N (STABiO™) was applied to improve the adhesion between the matrix and filler. The optimal manufacturing conditions (cross-linker amount, hot-press pressure, and time) were investigated. When 14.3 wt. % of the cross-linking agent to the total weight of CNF and CAB was added, the tensile strength and flexural strength were improved by 72.4% and 16.3%, respectively, compared with neat CAB. It was concluded that this increase in strength is a result of both: cross-linking between the CNF sheets as well as the cross linking occurring at the CNF/CAB interface.Документ Відкритий доступ Effect of nanoscale additives and ultraviolet stabilizers on the destruction of thin-layer coatings under the influence of UV radiation(Liha-Pres, 2023) Maniecki, Tomasz; Bilousova, AnnaThe destruction of paint and varnish coatings in atmospheric conditions is a problematic niche of today, which makes it urgent to identify the negative impact of nanoparticles on the stability of water repellency and the need for further research on improving the stability of water repellency for systems intended for use in atmospheric conditions. The author of the article investigates the effect of the introduction of nanoscale additives and ultraviolet stabilizers into thin-layer coatings on their destruction under the influence of ultraviolet radiation.Документ Відкритий доступ Expanding perlite materials to obtain coatings that repel water(Liha-Pres, 2023) Myronyuk, Oleksiy; Baklan, DenysThis paper explores a solution to the complex scaling, high cost and low environmental resistance associated with superhydrophobic coatings. By using organic coating technology, the paper demonstrates the possibility of obtaining highly water-repellent surface coatings based on expanded perlite and regenerated adsorbent. The study characterizes the properties of the coatings through various techniques and concludes that they serve as a good base coat for creating superhydrophobic volumetric hierarchical coatings. Additionally, the research shows that using an adsorbent for used refined sunflower oil is as effective as using freshly ground expanded perlite.Документ Відкритий доступ Nanosized additives and their impact on the fire resistance of coatings(Liha-Pres, 2023) Barrat, Silvère; Myronyuk, OleksiyThe study investigated the impact of different nanosized additives on the fire resistance properties of intumescent coatings. The results showed that the addition of organically modified montmorillonite and hydrophobized silica reduced the fire resistance properties of the coatings. This was due to the expansion processes being shifted to higher temperatures, which increased the time of direct heating of the substrate. However, minor concentrations of organically modified montmorillonite significantly changed the structure of the coatings and increased their specific heat insulation properties. The study also observed that nanosized additives had an effect on the expansion factor and foam structure of the coatings. This effect was suggested to be due to the complex influence of the nanoparticles on the bubble growth processes through the modification of melt viscosity. Overall, the study highlights the importance of carefully selecting the type and concentration of nanosized additives when designing intumescent coatings for fire protection applications.Документ Відкритий доступ Occurrence of microplastics in soil in recreational, residential, and industrial areas influenced by human activities(Liha-Pres, 2023) Tunali Mehmet Meric; Myronyuk, OleksiyPlastic pollution affects ecosystems worldwide, with microplastics (MPs) being a major concern. This study evaluates MP abundance in soils impacted by human activities in different areas in Istanbul. Results indicate recreational areas have the highest MP content, while residential areas have the lowest. Industrial areas have intermediate levels. Particle shapes vary by category, with fibers most prevalent in recreational areas. FT-IR spectrometry analysis identified the types of MPs present, with the recreational areas containing polymers undergoing hydrolysis. The industrial zone’s MP contamination was recent and relatively clean, while the PE plastic in Dilovası showed little weathering.Документ Відкритий доступ Spray-printing of composite gas diffusion electrodes with controllable porosity and hydrophobicity based on nanoparticles and polymeric binder(Liha-Pres, 2023) Liyong Xi; Puiki Leung; Yong ZuoThis research evaluates the effectiveness of various composite Gas Diffusion Electrode (GDE) architectures for carbon dioxide reduction. The study employs a flexible spray printing technique to create hydrophobic porous structures using a blend of carbon or metal nanopowders and a polymeric binder. The resulting porous layers serve as different electrode layers, including Gas Diffusion Layers (GDLs), Microporous Layers (MPLs), and catalyst supports, which can enhance the activity and hydrophobicity of GDEs. The study finds that the increased surface roughness (porous structures) and Polyvinylidene fluoride (PVDF) content in these porous layers improve their hydrophobicity/flooding tolerance. The study demonstrates that the selective production of ethylene can be sustained for over 10 hours at a high current density of –200 mA cm–2 when porous MPL and catalyst support layers are added. The use of hydrophobic porous structures as electrode layers can provide a cost-effective and scalable approach to enhance the hydrophobicity and activity of GDEs. Furthermore, the extended duration of electrolysis using these porous layers has the potential to create more efficient and sustainable electrocatalysts for carbon dioxide reduction.Документ Відкритий доступ The combined effects of UV radiation and water flow on the deterioration of water-repellent coatings with textures(Liha-Pres, 2023) Myronyuk, Oleksiy; Baklan, Denys; Rodin, Aleksej; Zuo YongA study analyzed micro- and nanotextured coatings resistance to UV radiation, water immersion, and flow. The coatings were created using modified calcium carbonate microparticles and treated colloidal silica nanoparticles. The study compared the aging of polymeric materials under UV radiation to hydrophobized particles and proposed a mechanism for organo-mineral coatings deterioration.Документ Відкритий доступ The effect of pyrogenic SIO2 nanoparticles on the photodegradation of polymer coatings when exposed to UV irradiation(Liha-Pres, 2023) Myronyuk, Oleksiy; Baklan, Denys; Bilousova, AnnaThe study investigates the impact of functionalized silica nanoparticles on the photodestruction of styrene acrylic polymer-based coatings. The research uses infrared spectroscopy, ablation speed, and water contact angle measurements to analyze the UV degradation of thin layer coatings under accelerated aging conditions. HALS amine loaded coatings are used as a reference. Results show that the photodegradation of the silica nanoparticles-polymer composite thin film coatings is influenced by two factors: screening of UV radiation and increased polymer hydrophilization speed. At nanoparticle loads over 15 wt. %, the thickness ablation speed decreases from 1.3 to 1.2 μm/h, and the contact angle sharply drops to 40 from the initial 89 within the first 30 minutes of exposure.Документ Відкритий доступ Thin film polymer composites incorporating red mud particles as agents for forming textured surfaces with water repellent properties(Liha-Pres, 2023) Myronyuk, Oleksiy; Baklan, Denys; Li CheThis study explores a potential approach to derive the foundation for water-resistant coatings from red mud. The process involves annealing to remove the water-soluble components of the waste. The research demonstrates that the utilization of stearic acid as a water-repellent agent yields the highest contact angle of 143. The findings indicate that red mud could be a viable source for producing hierarchical systems capable of achieving hydrophobicity, in addition to the conventional particulate fillers.Документ Відкритий доступ Аналіз впливу оксиду цинку на властивості полімерних композитів(Liha-Pres, 2023) Євпак, Вікторія; Мельник, ЛюбовВ даній статті розглянуто вплив нанодисперсного оксиду цинку на різні полімерні матриці. Проаналізовано дослідження з заданої теми, та виявлені зміни, що відбуваються при додаванні оксиду цинку до полімерної матриці. Проаналізовано залежність зміни механічних характеристик полімерного композиту від концентрації оксиду цинку.Документ Відкритий доступ Аналіз способів виробництва тонерів(Liha-Pres, 2023) Пєтухов, Аркадій; Шнирук, Олег; Маковський, ДенисДосліджено різні способи виробництва тонерів. Зразки отримані методами суспензійної та емульсійної полімеризації та полімеризацією міні-емульсії. Було простежено морфологічні характеристики виготовлених тонерів. Досліджувані тонери, отримані за схемою суспензії, виявили майже сферичну форму з найменшим розміром частинок – 4,95 мкм порівняно з емульсійними та міні-емульсійними продуктами полімеризації із середнім розміром частинок 12,03 і 16,07 мкм відповідно.Документ Відкритий доступ Аналіз факторів підвищення вогнестійкості тканих матеріалів(Liha-Pres, 2023) Мельник, Любов; Сорокіна, ІринаДосліджено вплив антипірену PVP (PR)-P-DCDA різних концентрацій на вогнестійкість бавовни. Зразки отримані методом просочення. Доведено, що обробка PVP (PR)-P-DCDA сильно впливає на стійкість до застосування полум’я. Результати TGA показали, що температура розкладання оброблених тканин була знижена шляхом обробки, а PVP (PR)-P-DCDA здатний захистити бавовну від термічної деградації та сприяти утворенню стабільного обвуглення. Встановлено, що додавання антипірену до бавовни зменшує займистість через дегідратацію PVP (PR)-P-DCDA до обвуглення, уповільнює довжину обвуглення, а також втрату маси зразків.Документ Відкритий доступ Високонаповнені полімерні композити, отримання та застосування(Liha-Pres, 2023) Сова, Надія; Слєпцов, Олександр; Розвора, ЛюбомирРобота присвячена аналізу технологій створення полімерних композиційних матеріалів на основі поліолефінів.Документ Відкритий доступ Вплив нанонаповнювача СaСО3 на деякі властивості поліетилену низької густини(Liha-Pres, 2023) Сингаївська, Катерина; Мельник, ЛюбовВ даній роботі було проведене дослідження впливу нанонаповнювача СaСО3 на деякі властивості поліетилену низької густини. Було з’ясовано, що додавання даного наповнювача до поліетилену низької густини (ПЕНГ) сприяє підвищенню міцності матеріалу без зміни температури плавлення та ступеня кристалізації, але при цьому знижується його пластичністьДокумент Відкритий доступ Електропровідні епоксикомпозити з вуглецевими нанотрубками(Liha-Pres, 2023) Солдатенков, Василь; Мельник, ЛюбовВ даній роботі розроблено методи одержання зразків на основі епоксидного зв’язуючого та вуглецевих нанотрубок; визна чено оптимальні технологічні режими їх виготовлення. Досліджено електричний опір розроблених композитів в залежності від концентрації вуглецевих нанотрубок.Документ Відкритий доступ Електропровідні композитні покриття. Отримання та властивості(Liha-Pres, 2023) Савченко, Богдан; Свістільнік, Роман; Федорів, ТарасРобота присвячена дослідженню впливу умов створення та типу устаткування на електропровідність полімерних композитних покриттів.Документ Відкритий доступ Енергетичний стан поверхні дисперсних оксидів(Liha-Pres, 2023) Береговий, Тарас; Мережко, Ніна; Свідерський, Валентин; Нудченко, ЛюдмилаЕфективність застосування дисперсних оксидів в складі композиційних матеріалів різного функціонального призначення в значній мірі визначається фізико-хімічними властивостями їх поверхні. Не менш важливим фактором являється і стабільність останніх в процесі експлуатації. Однак дані дані відносно таких особливостей дуже обмежені, тому метою статті є кількісна оцінка складу, енергетичного стану та адсорційної здатності ряду оксидів II–IV груп періодичної системи, що використовуються в якості наповнювачів або слугують складовими компонентами різних композитів. Методами, що базуються на різних фізичних принципах (змочуваності полярними і неполярними рідинами, діелектричними властивостями, ІЧ-спектроскопія, комплексний термічний аналіз) оцінений енергетичний стан поверхні дисперсних оксидів та його зміни в процесі дії вологого середовища з мікроорганізмами. Виявлено рівень розвитку деструкційних процесів та найбільш стабільні оксидні матеріали (Al2O3 та його модифікації). Одержані результати можуть знайти застосування в промислових і біологічних процесах.Документ Відкритий доступ Застосування технології адитивного виробництва у створенні теплопровідних полімерних композитів(Liha-Pres, 2023) Савченко, Богдан; Пушкарьов, ДенисРобота присвячена висвітленню питання можливості застосування технології адитивного виробництва для створення виробів на основі полімерних композиційних матеріалів з покращеними теплопровідними властивостями.Документ Відкритий доступ Полімеркомпозиційне покриття із застосуванням червоного шламу(Liha-Pres, 2023) Мельник, Любов; Салата, Тимур; Коренко, Дар’яВ ході проведення досліджень розроблено технологію виготовлення композиційних матеріалів типу покриттів на основі системи POLICRIL 590-ЧШ з попередньою обробкою ЧШ стеариновою кислотою. Одержано зразки (вільні плівки та покриття) розроблених композицій в широкому концентраційному інтервалі ЧШ: 5–25 мас. % та різним вмістом СК 1–3 мас. % від маси ЧШ. Всі розроблені покриттів є гідрофільними, їх кут змочування не перевищує 90. А ефективний модуль пружності в залежності від концентрації ЧШ, має лінійний характер і при збільшенні вмісту ЧШ з 5 до 25 мас. % збільшується з 102 до 263 МПа. Введення 1 мас. % СК дозволяє підвищити цей показник в 1,5–2,5 рази.Документ Відкритий доступ Підвищення механічних властивостей матеріалів на основі надвисокомолекулярного поліетилену(Liha-Pres, 2023) Кравець, Тетяна; Мельник, ЛюбовВ даній роботі було досліджено вплив поліетиленглі колю (PEG) та поліетилену високої щільності (HDPE) на механічні властивості поліетилену надвисокої молекулярної маси (UHMWPE). Додавання HDPE покращує механічні властивості (міцність на роз- рив, міцність на вигин, ударна в’язкість, модуль пружності при вигині) у співвідношенні UHMWPE/HDPE – 60/40. Хоча при додаванні PEG покращується технологічність UHMWPE, але погіршуються механічні властивості суміші.