2021
Постійне посилання на фонд
Переглянути
Перегляд 2021 за Назва
Зараз показуємо 1 - 20 з 34
Результатів на сторінці
Налаштування сортування
Документ Відкритий доступ Analysis of the Efficiency of the Kalman-Type Correlation Algorithm for Tracking of a Small UAV in the Presence of Uncorrelated(КПІ ім. Ігоря Сікорського, 2021) Herasymenko, A. O.; Zhuk, S. Ya.The article shows the relevance of the problem of development and analysis of algorithms for tracking small-sized UAVs according to video surveillance. A Kalman-type correlation algorithm for tracking of a small-sized UAV in the presence of spatially uncorrelated interference, which is the most common in practice, is synthesized. In the obtained algorithm, the UAV motion parameters are estimated independently along the axes of a rectangular coordinate system. Positioning accuracy analysis using the correlation algorithm, as well as the correlation algorithm for tracking UAVs based on the Kalman filter, was carried out by statistical modeling in the Matlab programming environment.Документ Відкритий доступ Detection Filter Method in Diagnostic Problems for Linear Dynamic Systems(КПІ ім. Ігоря Сікорського, 2021) Volovyk, A. Yu.; Kychak, V. M.Документ Відкритий доступ Features of Low-Intensity Energy Balance in the Process of Physiotherapeutic Application of Mixtures of Natural Materials(КПІ ім. Ігоря Сікорського, 2021) Yanenko, О. P.; Peregudov, S. М.; Shevchenko, К. L.; Golovchanska, О. D.The authors investigated the features of energy balance that provide the process of using natural materials in physiotherapeutic thermal procedures. Substances such as ozokerite, paraffin, naphthalene, muds and their combinations are widely used in physiotherapy, so it is important not only to know the parameters of the heat exchange, but also the distribution of other types of energy that can affect the effectiveness of treatment. The authors theoretically substantiated and experimentally proved that microwave component is presented in the radiation spectrum of the ozokerite applicator. The level of radiation in the millimeter range of the applicator with a size of 10×10 cm is compared with the level of low-intensity signals of technical devices for millimeter therapy. The dynamic change of the radiation level of the microwave component during the cooling of the applicator from the maximum temperature of 50∘С to the temperature of the human body surface was investigated. It was revealed that the sign of the radiation of the millimeter component in relation to the human body changes. This results in the formation of positive and negative low-intensity flows of microwave radiation. The frequency ranges of these flows and their level were investigated. It has been found that changing the percentage of paraffin in ozokerite can affect the level and range of negative microwave flows. The results of previous studies by the authors, which substantiate the positive effect of negative flows, including ozokerite-paraffin therapy, in inflammatory processes with ”excess energy” and other diseases, are adduced. The microwave electromagnetic radiation studied by the authors is a concomitant factor during the relevant physiotherapeutic procedures, in particular heat treatment. However, this factor can significantly affect the functional state of the human body, so it must be taken into account during physiotherapy procedures.Документ Відкритий доступ Household Induction Cookers: Calculation and Design of Structural Elements(КПІ ім. Ігоря Сікорського, 2021) Pantelyat, M. G.; Hryshchuk, Yu. S.; Chepeliuk, O. O.; Yeloiev, A. K.A technique for calculation and design of main structural elements of household induction cookers – inductors and magnetic cores is proposed. The technique consists of two stages. The first stage has been developed on the basis of engineering methods for calculating copper inductors of industrial induction heaters, taking into account the design features and operating modes of induction cookers, done in steps such as selection of geometrical dimensions of the inductor, calculation of main electrical and energy indicators of the inductor, calculation of the system ”inductor-dishes”, determination of the number of turns of the inductor and calculation of the width of the turn. The second stage represents an engineering approach for the calculation and design of magnetic cores made of MnZn ferrites, done in steps such as choice of material for the manufacture of magnetic core rods, choice of geometric dimensions of ferrite rods, calculation of the mass of the magnetic core and calculation of power losses in the magnetic circuit. The calculation results and designs of the inductors and magnetic cores with respect to a number of modes of heating of dishes of various geometric sizes are presented and analyzed. The developed techniques and the results obtained on its base are supplemented and supported by preliminary numerical analysis of the electromagnetic field distribution in induction cookers and heated dishes as well as by experimental research on the workbench developed. Conceptual designs of induction cookers developed by using the proposed approaches illustrate the techniques presented. The developed techniques can be used in the process of research and design of structural elements of household induction cookers, as well as in the educational process for the preparation of Bachelors and Masters in relevant educational programs.Документ Відкритий доступ Investigation of Lung Sounds Features for Detection of Bronchitis and COPD Using Machine Learning Methods(КПІ ім. Ігоря Сікорського, 2021) Porieva, H. S.; Ivanko, K. O.; Semkiv, C. I.; Vaityshyn, V. I.Документ Відкритий доступ Mathematical Modelling of Rod-Type Piezo-Electric Transducers for Acoustoelectronic Devices(КПІ ім. Ігоря Сікорського, 2021) Bazilo, C. V; Bondarenko, M. O.; Khlivnyi, V. V.; Tomenko, M. H.; Tomenko, V. I.The work is devoted to the peculiarities of the construction and study of mathematical models of rodtype piezoelectric transducers, which are widely used in various acoustoelectronic devices (hydroacoustic means of target detection, ultrasonic non-destructive testing, medical diagnostics, etc.). In contrast to the existing mathematical models of piezoelectric transducers (based on amplitude-phase dependences, resonant piezoelectric transducers, equivalent circuits, etc.), the proposed mathematical model makes it possible to establish a dependence, which is a mathematical description of the acoustic coupling that exists in a solid piezoceramic rod between wave fields on its various areas. An algorithm for calculating a mathematical model of rod-type piezoelectric transducers is presented and based on the determination of the transformation ratio in the case of the inverse piezoelectric effect. Analytical dependencies, which make it possible to determine the electrical impedance and the amplitude value of the potential in the electrical circuit of the piezoelectric transducer, are obtained. It is shown that these dependencies underlie the expression for determining the transformation ratio, which is a mathematical model of a rod piezoelectric transducer. At the same time, the principle of operation of such a transducer provides for the use of longitudinal vibrations in a prismatic rod. The results of the mathematical modelling are presented on the example of a rod transducer with a square cross-section made of piezoelectric ceramics of the PZT type (plumbum zirconate titanate). The performed comparisons of the calculated and experimentally obtained values of the frequency dependence of the modulus of the transformation ratio of the piezoceramic transducer showed a high convergence between them (the discrepancy between the results of mathematical modelling and the experimentally obtained data for the same value of the operating frequency does not exceed 8.5%).Документ Відкритий доступ Method for Blink Detection in Single Channel of Invasive Electromyogram Signal(КПІ ім. Ігоря Сікорського, 2021) Bobrov, A. L.; Borysenko, O. M.; Popov, A. O.Problem statement. Facial nerve damage is the cranial nervous system disorder often leading to facial muscle paralysis, which might be effectively restored using functional electrical stimulation of the fully or partially denervated circular muscle of the eye to achieve muscle contraction to close the eyelids. To control the invasive stimulation system, the automated detection of the blink event in the intact eye is used as a trigger. To achieve this, the new approach to single channel invasive electromyogram (EMG) signal analysis is proposed. Materials and Methods. The combined time-spectral approach to blink detection consists of the two stages, starting from the thresholding of filtered EMG signals in the sliding window, which is followed by comparing the total spectral power in the Fourier domain to minimum and maximum thresholds. If both conditions are met, the EMG in the current window is considered to contain the blink event. In the experiment, the EMG data recorded from the one male adult healthy volunteer is used, the signal contained an acceptable amount of artefacts and was recognized as reflecting the usual EMG. The true positive rate (TPR), positive predictive value (PPV), False Discovery Rate (FDR), and False Negative Rate (FNR) is used as a performance metrics. Results. In the result of applying the proposed blink detection algorithm with 500 ms duration of the time window and 100 ms overlap, the following performance metrics are obtained: TPR=93%, PPV=63%, FDR=7%, FNR=37%. Impact. Acceptable true positive rate of blink detection suggests the method is promising for wider applications in the clinical settings and might be incorporated in the prototypes of implanted systems for facial muscle paralysis restoration using functional electrical stimulation for further development.Документ Відкритий доступ Optimum Coherent and Incoherent Demodulators of BPSK and DBPSK Radio Signals with Manchester Encoding(КПІ ім. Ігоря Сікорського, 2021) Parfeniuk, V. H.; Sabadash, S. S.; Stavisiuk, R. L.Algorithms and schemes of optimal coherent and incoherent demodulators of binary radio signals with phase and differential phase shift-keying (DPSK) with Manchester encoding of the modulating signal are proposed. The use of DPSK makes it possible to effectively deal with the phase ambiguity of the reference oscillation generator of the correlation receiver. This solution allows you to overcome the so-called «reverse work» effect in the demodulator of signal with phase-shift keying. Differential and Manchester encoding finds it’s application in various areas of use of digital systems for information transmission (DSIT): from local and personal area networks, to space optical communication systems. There are many types of DSIT: radio communication systems (in the Bluetooth standards, in NFC technology, as well as in high-resolution space remote sensing (SRS)), wired data transmission systems (in the local area networks of the Ethernet family), so are optical communication systems (FSO, ISOWC and SpaceWire). It’s shown that the joint use of DPSK and Manchester encoding provides higher noise immunity when used in DSIT and retain the advantages of Manchester encoding with respect to symbolic synchronization of the demodulator. The given algorithms and schemes are based on the use of reception in general and the features of Manchester encoding, which allows using the full energy of the information bit for demodulation. To assess the potential noise immunity of the proposed demodulator schemes, it’s assumed that the modulated signals are orthogonal in the amplified sense. The conducted mathematical modeling of the proposed technical solutions confirmed their operability and higher noise immunity compared to the symbol by-symbol reception. It’s proposed to use the developed algorithms and schemes of demodulators in the receivers of the SRS with high resolution, in the receivers of optical communication systems and in the receiving part of the equipment of local networks of the Ethernet family.Документ Відкритий доступ Pекомендацiї щодо реалiзацiї методу управлiння потоком даних на основi рiзних прiоритетiв в стацiонарнiй компонентi системи зв’язку Збройних Сил України(КПІ ім. Ігоря Сікорського, 2021) Добришкiн, Ю. М.; Лаппо, I. М.; Кузнецов, В. О.; Геращенко, М. М.Актуальнiсть. Задача пiдвищення продуктивностi стацiонарного компонента системи зв’язку Збройних Сил України (ЗС України) потребує впровадження вiдповiдних нових методiв управлiння потоком даних на основi рiзних прiоритетiв, якi в подальшому мають бути реалiзованi в сучасних протоколах маршрутизацiї у вiдповiдностi з концепцiєю мереж наступного поколiння. Метод. Дослiджено метод управлiння потоком даних на основi рiзних прiоритетiв в iнформацiйно-телекомунiкацiйнiй мережi стацiонарного компоненту системи зв’язку Збройних Сил України, який складається з наступних етапiв: монiторинг та аналiз вихiдних даних; формування вектору шуканих параметрiв; формування метрик використання ресурсiв мережi; постановка математичної задачi оптимiзацiї; розв’язання задачi оптимiзацiї. За результатами дослiдження встановлено, що в рамках методу забезпечується узгоджене розв’язання задач багатошляхової маршрутизацiї i адаптивного обмеження iнтенсивностi потоку на границi iнформацiйно-телекомунiкацiйної мережi на основi рiзних прiоритетiв. Результати. В статтi дослiджено метод на конкретному прикладi структури мережi з використанням iнструментарiю ”Optimization Toolbox” програмного пакета Matlab. Розробленi практичнi рекомендацiї щодо практичної реалiзацiї методу в стацiонарнiй компонентi системи зв’язку ЗС України. Висновки. За результатами моделювання встановлено, що реалiзацiя методу в сучасних технологiчних рiшеннях дозволить пiдвищити продуктивнiсть iнформацiйно-телекомунiкацiйної мережi у середньому на (10-20)%, а також якiсть обслуговування з ймовiрнiстю доставки пакетiв на (1-3)%. Запропонований метод вiдповiдає вимогам концепцiї управлiння потоком даних Traffic Engineering. Зазначено, що для перевiрки адекватностi та достовiрностi удосконаленого методу в подальшому необхiдно провести натурний експеримент на реальному мережевому обладнанi.Документ Відкритий доступ Pозрахунок ймовiрностi виявлення радiосигналiв у залежностi вiд технiчних характеристик засобу радiомонiторингу(КПІ ім. Ігоря Сікорського, 2021) Слюсарчук, О. О.У сучасному свiтi розподiл радiочастотного ресурсу жорстко контролюється державними органами країн для якiсної роботи рiзних систем радiозв’язку, радiолокацiї та радiонавiгацiї, якi працюють в iнтересах рiзних служб. Завдяки сучасним радiозасобам можливо забезпечити зв’язок, незалежно вiд географiчного розташування кореспондентiв. Пiд час налаштування нових систем радiозв’язку, пошуку нових джерел радiовипромiнювань, здiйснення контролю за радiовипромiнюючими засобами досить часто постає питання розрахунку ймовiрностi виявлення певного радiосигналу iснуючим складом апаратури, яка має визначенi технiчнi характеристики. Метою запропонованої статтi є розрахунок ймовiрностi виявлення радiосигналiв у залежностi вiд технiчних характеристик засобу радiомонiторингу при веденнi пошуку, при умовi, що частота роботи радiосигналу знаходиться в межах дiапазону пошуку та енергетичнi параметри сигналу є достатнiми для його виявлення. У статтi проаналiзованi iснуючi пiдходи до визначення ймовiрностi виявлення радiосигналiв у радiомережах (радiонапрямках) при визначених частотно-часових характеристиках радiоприймальних пристроїв. Крiм того запропоновано науково-методичний апарат, який доцiльно використовувати пiд час планування виконання завдань пошуку нових джерел радiовипромiнювань. В результатi проведення дослiджень, було встановлено залежнiсть ймовiрностi виявлення радiосигналiв вiд частотно-часових характеристик радiоприймального пристрою. Крiм того у статтi наведенi графiки залежностi ймовiрностi виявлення радiосигналiв вiд часових характеристик радiоприймального пристрою, якi побудованi вiдповiдно до запропонованого науково-методичного апарату та за допомогою програмного забезпечення ”Mathcad 14.0”, а також визначенi шляхи пiдвищення ймовiрностi виявлення радiосигналiв. Зокрема, для пiдвищення ймовiрностi виявлення радiосигналiв необхiдно зменшувати дiапазон пошуку частот та часовi характеристики технiчних процесiв радiоприймального пристрою. Крiм того доцiльно розглядати можливiсть збiльшення часу пошуку сигналу та смуги пропускання радiоприймального пристрою. Науково-методичний апарат, який описаний в статтi, може бути використаний пiд час дослiдження апрiорних результатiв пошуку нових джерел радiовипромiнювань визначеним складом апаратури з певними технiчними характеристиками.Документ Відкритий доступ Rotations of Cylindrical Dielectric Resonators in a Rectangular Waveguide(КПІ ім. Ігоря Сікорського, 2021) Trubin, A. A.The coupling coefficients of cylindrical dielectric resonators with a regular rectangular waveguide under the condition their axes rotation are calculated. The dependences of the coupling coefficients on the angles of rotation and transverse coordinates of the resonator in the case of excitation of the main magnetic types of natural oscillations in them are considered. The dependence of the coupling value on the angles of rotation at the points of circular polarization of the fundamental wave of a rectangular waveguide is shown. The condition for the angle of rotation of the axis of the resonator, determined by the dimensions of the cross section of the waveguide and the frequency of the main type of natural oscillations, is also established, when fulfilled, the coupling coefficient becomes constant in the transverse plane of symmetry of the waveguide. New analytical expressions are derived for the mutual coupling coefficients of identical cylindrical dielectric resonators when their axes rotate relative to a rectangular waveguide. The dependences of the mutual coupling coefficients on the angles of rotation and coordinates of the resonators are investigated. Conditions are found under which the mutual coupling coefficients of two cylindrical resonators are independent of their transverse coordinate in the plane of symmetry of the waveguide. The reasons for the change in the sign of the coupling coefficients of the resonators during their rotation are discussed. The effect of the emergence of coupling extrema for different relative orientations of dielectric resonators is noted. In particular cases of parallelism of the resonator axes of one of the coordinate axes of the waveguide, the analytical expressions found in the work coincide with those obtained earlier. The obtained analytical results make it possible to construct analytical models of bandpass and notch filters, significantly reduce the computation time and optimize complex multi-cavity structures of microwave and optical communication systems.Документ Відкритий доступ Scattering of Electromagnetic Waveson Lattices of Rectangular Dielectric Resonators(КПІ ім. Ігоря Сікорського, 2021) Trubin, A. A.Документ Відкритий доступ Solving the Inverse Problem of Relationship Between Action Potentials and Field Potentials in Cardiac Cells(КПІ ім. Ігоря Сікорського, 2021) Ivanushkina, N. G.; Ivanko, K. O.; Shpotak, M. O.; Prokopenko, Y. V.Multiple electrode array (MEA) systems are the instrument platforms being used for cardiac extracellular electrophysiology investigation. Key applications of MEA technology are disease modeling and screening of drug effects. To solve these problems the efforts of many scientists are directed to signal processing and analysis of field potentials (FP) measured with MEA systems. However, it should be noted the complexity of interpretation of MEA information in non-invasive field potentials measurements of cardiac cells compared to invasive action potential (AP) recordings obtained using patch clamp technology. This study is devoted to the mathematical determination of the relationship between the signals of the electrical activity of cardiomyocytes: internal AP and external FP. Derivation of equations for transfer functions between AP and FP is based on field theory. This article provides a solution to the inverse problems of the relationship between AP and FP. Numerical experiments demonstrate the results of the inverse transformation of simulated field potentials signals. To denoise the potentials of the extracellular field of cardiomyocytes, the method combining wavelet transform and processing in eigensubspaces of cardiac cycles is used. The proposed method, based on transfer functions, can be used to determine AP parameters and expand the capabilities of data analysis in MEA systems for diagnosing heart disease and assessing cardiac toxicity during drug development.Документ Відкритий доступ Spectrum Smoothing Method for OFDM Signals Detection in Frequency Selective Channel(КПІ ім. Ігоря Сікорського, 2021) Buhaiov, M. V.Orthogonal Frequency Division Multiplexing (OFDM) technology has become widespread in civil and military radio systems, especially in channels with frequency selective fading. Due to the large number of OFDM signal schemes, an urgent task for modern radio monitoring systems is development of methods and algorithms for detecting such signals that will be stable in the uncertainty of OFDM signal structure and electromagnetic environment. At the stage of detection, the characteristic feature of OFDM signal is presence of frequency channels in its spectrum envelope. In this research, an algorithm for detecting an OFDM signal in the frequency domain and for estimating the number of frequency channels and duration of the interval of orthogonality was developed. To make a decision whether signal is present in realization of the normalized to the energy spectrum, its variation was used. This approach avoids estimating noise power. In case of signal samples detecting spectrum is double-smoothed using moving average. This provides better smoothing than with a single long window. Thereafter, double thresholding is performed. The second threshold is calculated using samples that have not exceeded the first threshold. Samples that have exceeded the second threshold are considered signal. Next, a search is made for occupied frequencies with a given bandwidth. The samples located in this band are re-smoothed and give spectrum trend, which is used as a threshold to determine the boundaries of frequency channels. OFDM signal is considered detected if equidistant frequency channels were found. After that, duration of the interval of orthogonality is calculated. The proposed method requires a slight complication of the spectral analysis procedure based on the fast Fourier transform. Proposed method can be used for improving broadband radio monitoring systems and provide practically simultaneously implementation procedure of OFDM signal detection-recognition.Документ Відкритий доступ Synthesis of Extremely Wide Stopband E-plane Bandpass Filters(КПІ ім. Ігоря Сікорського, 2021) Zhuk, S. Ya.; Omelianenko, M. Y.; Romanenko, T. V.; Tureeva, O. V.Документ Відкритий доступ The Experimental Study of the Cerium Dioxide Silicon Interface of MIS Structures(КПІ ім. Ігоря Сікорського, 2021) Korolevych, L. M.; Borisov, A. V.; Voronko, A. O.The article is devoted to the actual task of studying a dielectric, which is an alternative to silicon dioxide in metal-insulator-semiconductor (MIS) structures. In metal-silicon dioxide-silicon structures, upon going to nanosize, the thickness of the dielectric film decreases so much that it becomes tunnel-transparent and its breakdown voltage decreases. These phenomena can be eliminated by replacing silicon dioxide with a dielectric with a higher dielectric constant. These dielectrics primarily include oxides of transition and rareearth metals. The parameters and characteristics of the MIS structure are determined by various factors, but the properties of the dielectric and the dielectric-semiconductor interface play a special role. In previous works of the authors, it was theoretically proved that cerium dioxide from a number of candidate dielectrics should have the best quality of the interface with silicon. This work is devoted to a study aimed at determining the flat-band voltage and capacitance of MIS structures and at assessing the quality of the cerium dioxidesilicon interface. The study is carried out by the method of capacitance-voltage characteristics. For this, the high-frequency capacitance-voltage characteristics of the aluminum – cerium dioxide – silicon structures were measured at different temperatures. The capacity of the space charge region (SCR) in the enrichment and weak inversion modes of the near-surface layer of a semiconductoris considered. It is shown that the dependence of this capacitance in the (–2) degree on the voltage at the metal electrode c−s2(VG) is linear. The intersection of this line with the abscissa axis makes it possible to determine the flat-band voltage. The slope tangent of this linear dependence makes it possible to determine the energy density of the charge at the dielectric–semiconductor interface. It is shown that the charge density at the cerium dioxide – silicon interface corresponds to the minimum values of the charge density at the silicon dioxide – silicon interface. The absence of a shift in the capacitance-voltage characteristics of the structures under study with a change in temperature indicates the stability of the charge at the cerium dioxide - silicon interface.Документ Відкритий доступ Використання функцiй Уолша для пiдвищення енергетичної прихованостi цифрової радiолiнiї(КПІ ім. Ігоря Сікорського, 2021) Андреєв, О. В.; Дубина, О. Ф.; Нiкiтчук, Т. М.; Ципоренко, В. В.Для передачi аналогових сигналiв по каналах радiозв’язку у районах зi складним рельєфом мiсцевостi широко використовується короткохвильовий та ультракороткохвильовий дiапазони. При цьому бiльшiсть засобiв радiозв’язку використовують частотну модуляцiю передавача при обмеженiй смузi частот. Такi сигнали мають достатньо високу спектральну щiльнiсть потужностi, що дає змогу виявляти i перехоплювати повiдомлення, якi передаються. У сучасних телекомунiкацiйних системах при передачi даних по радiоканалу НВЧ дiапазону широко використовуються сигнали, ширина спектру яких перевищує смугу частот, що необхiдна для передачi даних iз визначеною швидкiстю. Це забезпечує багатоканальну передачу цифрових даних на однiй несучiй в НВЧ дiапазонi з необхiдними показниками якостi. В умовах iснуючих обмежень на потужнiсть передавача, необхiдна дальнiсть радiолiнiї забезпечується шляхом адаптивної змiни як тривалостi передавання, так i параметрiв модуляцiї радiосигналу. Однак, тривалiсть передачi у реальному часi цифрового сигналу мови iз визначеною шириною спектру не може перевищувати значення перiоду дискретизацiї сигналу. У статтi запропонований варiант використання функцiй Уолша для розширення спектру сигналу цифрової радiолiнiї в умовах обмежень як на потужнiсть, так i на тривалiсть випромiнення радiосигналу. Проведена оцiнка умов виявлення випромiнювання передавача широкосмугової цифрової радiолiнiї засобами частотного монiторингу.Документ Відкритий доступ Волноводный поляризатор для радиолокационных и спутниковых систем(КПІ ім. Ігоря Сікорського, 2021) Булашенко, А. В.; Пильтяй, С. И.; Калиниченко, Е. И.; Забегалов, И. В.Представлены результаты разработки нового поляризатора для спутниковых телекоммуникационных и радиолокационных систем, которые используют поляризационную обработку сигналов. Антенны таких систем позволяют работать на одной или двух ортогональных круговых поляризациях одновременно. Антенны, использующие круговую поляризацию, обеспечивают ряд преимуществ радиотехническим системам, в состав которых они входят. Для круговой поляризации уровень принимаемого сигнала является постоянным и независимым от ориентации антенны. Кроме того, для передающей и приемной антенн отсутствует необходимость четкой ориентации по углу в плоскости, перпендикулярной направлению радиолинии. Разработанный в статье поляризатор предназначен для применения в спутниковых телекоммуникационных и радарных системах и позволяет улучшить общие характеристики радиотехнической системы. Устройство создано на основе квадратного волновода с четырьмя штырями и одной диафрагмой и работает в диапазоне частот от 11.7ГГц до 12.5ГГц. В работе была создана математическая модель волноводного поляризатора и построены его электромагнитные характеристики. Среди этих характеристик были исследованы дифференциальный фазовый сдвиг, коэффициент стоячей волны по напряжению, коэффициент эллиптичности, кроссполяризационная развязка. Для проверки правильности модели, полученные характеристики математической модели было сравнено с результатами моделирования устройства с помощью метода конечных элементов и метода конечных разностей. Созданная математическая модель дает возможность эффективно анализировать характеристики поляризатора при изменении конструктивных параметров. К этим параметрам относятся размер стенки квадратного волновода, высоты диафрагм и штырей, расстояние между ними, толщина диафрагм и штырей. Было получено оптимальные размеры элементов конструкции поляризатора, которые обеспечивают эффективные поляризационные характеристики и его согласование.Документ Відкритий доступ Двополюсна схема заміщення електричного кола постійного струму з залежними джерелами напруги еквівалентна за потужністю(КПІ ім. Ігоря Сікорського, 2021) Артеменко, М.Ю; Петров, Д.О.; Кутафiн, Ю.В.Вiдомий понад столiття принцип еквiвалентного джерела, сформульований у виглядi теорем Тевенена та Нортона, нещодавно був удосконалений I. Барбi уведенням вимоги енергетичної еквiвалентностi первинного кола та його двополюсної схеми замiщення. Проаналiзовано особливостi та недолiки iснуючих двополюсних схем замiщення електричного кола постiйного струму (ЕКПС), еквiвалентних первинному колу за потужнiстю, та сформульована мета роботи: втiлення нового енергетичного змiсту принципу еквiвалентного джерела для класу ЕКПС, що мiстять як незалежнi, так i залежнi джерела напруги й резистори, шляхом розроблення нової двополюсної схеми замiщення та дослiдження умов узгодження ї ї навантаження для досягнення максимального ККД. Запропонована перша в цьому класi ЕКПС чотирьохелементна двополюсна схема замiщення, яка вiдрiзняється вiд схемного еквiвалента Барбi наявнiстю джерела струму, керованого струмом навантаження, вихiднi затискачi якого приєднанi до джерела напруги еквiвалентного генератора. Вiдомi формули розрахунку параметрiв елементiв двополюсних схемних еквiвалентiв Тевенена та Нортона були доповненi новими аналiтичними залежностями параметра залежного джерела струму вiд векторних i матричних коефiцiєнтiв макромоделi первинного кола в базисi контурних струмiв та експериментальних даних дослiдiв розриву й замикання вихiдних полюсiв. Також встановленi новi аналiтичнi спiввiдношення для розрахункiв узгодженого опору навантаження та величини максимального ККД нової двополюсної схеми замiщення. Достовiрнiсть результатiв дослiдження пiдтверджена еквiвалентнiстю отриманих формул вiдомим спiввiдношенням, справедливим для iншого класу ЕКПС, та вiртуальними експериментами з дослiдження ват-вольтних характеристик i максимiзацiї ККД первинного кола. Отриманi результати можуть бути використанi для енергетичної оптимiзацiї ЕКПС, пiдсилювальнi та перетворювальнi елементи яких працюють в лiнiйному режимi роботи, що моделюються залежними джерелами напруги.Документ Відкритий доступ Демодуляцiя енергетично прихованих лiнiйно-частотно-модульованих сигналiв(КПІ ім. Ігоря Сікорського, 2021) Стейскал, А. Б.; Ковтун, С. О.; Войтко, В. В.; Огарок, А. П.У статтi проведено аналiз дiаграми невизначеностi прямокутного лiнiйно-частотно-модульованого радiоiмпульсу. Виявлено характернi унiкальнi ознаки i особливостi перерiзу дiаграми невизначеностi. Запропоновано пiдхiд до демодуляцiї прийнятого енергетично прихованого лiнiйно-частотномодульованого сигналу на основi використання властивостей дiаграми невизначеностi елементарного радiоiмпульсу. Обґрунтовано можливiсть його демодуляцiї. Для реалiзацiї поставленої задачi запропоновано нове використання вiдомої схеми кореляцiйного приймача розрiзнення двох сигналiв з випадковими початковими фазами. Для чого визначено та розраховано параметри налаштування схеми кореляцiйного приймача (значень неузгодженостi за часом та частотою), за яких можливо однозначно приймати рiшення про прийнятий двiйковий символ у процесi демодуляцiї лiнiйночастотно-модульованого сигналу на основi отриманого значення вихiдного сигналу корелятора. Проаналiзовано залежностi вихiдного вiдношення сигнал/шум приймача вiд параметрiв лiнiйно-частотномодульованого сигналу. З урахуванням граничних значень параметрiв цих сигналiв при використаннi їх системами зв’язку оцiнено дiапазони бiтового iнтервалу та девiацiї частоти, якi потенцiйно можуть бути на входi приймального тракту. Проведено iмiтацiйне моделювання процедури демоделювання за допомогою програмних пакетiв Matlab R2016a та MathCAD 14. Результати моделювання пiдтверджують здатнiсть запропонованого алгоритму демодулювати лiнiйно-частотно-модульований сигнал у вхiднiй сумiшi при малих вiдношеннях сигнал/шум. У ходi аналiзу кiлькiсної мiри завадостiйкостi запропонованого приймача зроблено висновок про добру узгодженiсть результатiв моделювання з розрахунками. Спосiб демодуляцiї енергетично прихованого лiнiйно-частотно-модульованого сигналу, що пропонується, може бути впроваджений на вже iснуючих засобах радiомонiторингу або використаний при розробленнi нових засобiв, що працюватимуть з широкосмуговими сигналами.