2019
Постійне посилання на фонд
Переглянути
Перегляд 2019 за Дата публікації
Зараз показуємо 1 - 20 з 27
Результатів на сторінці
Налаштування сортування
Документ Відкритий доступ Підвищення ефективності методів пошуку сенсора, що відмовив, у надлишкових вімірювчах кутової швидкості(КПІ ім. Ігоря Сікорського, 2019) Горєлов, Є. М.; Збруцький, О. В.; Щоголєва, С. Г.; Янкелевич, Г. Є.Документ Відкритий доступ Вплив гнучкості несучої поверхнi літального апарату на її властивості(КПІ ім. Ігоря Сікорського, 2019) Мединський, В. В.; Зінченко, Д. М.Документ Відкритий доступ Вплив на аеродинамічні характеристики гвинтових рушіїв, що встановлені на кінцях крила(КПІ ім. Ігоря Сікорського, 2019) Поваров, С. А.Документ Відкритий доступ Numerical simulation of bellows compensators stress-strain state in air intake system(КПІ ім. Ігоря Сікорського, 2019) Trubachev, S. I.; Alekseychuk, O. M.У роботі представлено чисельне моделювання напружено-деформованого стану сильфонного компенсатора у системі забору повітря літака. Сильфонні компенсатори є невід’ємною частиною багатьох систем подачі повітря чи рідин у багатьох установках та транспортних засобах. Для розв’язання задачі про визначення напружено-деформованого стану сильфонного компенсатора у системі забору повітря літака аналітичні методи є неефективними внаслідок складної геометрії, тому доцільно застосовувати чисельні методи розрахунку. Для побудови скінчено вимірної моделі застосовувались тривимірні скінченні елементи у вигляді тетраедра. Було проведено аналіз напружено-деформованого стану сильфонного компенсатора та його основних складових: карданного кільця, хрестовини, внутрішнього кільця шарніра, зовнішнього кільця шарніра.Документ Відкритий доступ Synthesis of inertial positioning algorithm(КПІ ім. Ігоря Сікорського, 2019) Bondarenko, O. M.; Chornomorets, R. V.Представлено метод визначення координат із використанням вбудованих у мобільний телефон інерціальних датчиків. Роботу методу показано на прикладі декількох експериментальних результатів.Документ Відкритий доступ Дослідження моделей перехідної характеристики термопари(КПІ ім. Ігоря Сікорського, 2019) Козир, О. В.; Туз, Ю. М.Документ Відкритий доступ Цифровий метод корекції температурної похибки вимірювання тензодатчиком(КПІ ім. Ігоря Сікорського, 2019) Кузьмич, Л. В.This article is aimed at finding the opportunities to improve the remote measurements accuracy and noise immunity of the stress - strain state measuring, in particular in a detailed study of the polynomial coefficients behavior for the most used temperatures range of load cells. Based on the analysis of destabilizing factors, it is established that among the main destabilizing factors that limit the measurement accuracy of instrument systems equipped with strain gauges are the effects of external climatic and mechanical factors, in particular temperature, humidity and so on. The temperature change range influence on the most common materials used for the of strain gauges manufacturing, namely, karma and constan, alloys with a minimum temperature coefficient of resistance, is investigated The variation of the temperature error values ( 10%) on the rms error of the approximation error by power polynomials was investigated. The NUMERY package determines the dependence of the approximation error on the order of the approximating polynomial revealed that over a wide temperature range the errors for the karma and the constan have a weak relationship with the polynomial order. Calculations indicate that by narrowing the temperature range the error sharply depends on the order of the approximating polynomial, and at the sixth order it almost becomes zero. The effect of tabulated accuracy recording on polynomial coefficients was also investigated, and it was determined that a random error in the coefficients determination up to 10% for the karma and the constan practically does not affect the mean square error of approximation. The influence of the temperature range changing and the temperature error values variation on the rms error of the approximation error by power polynomials is investigated. The NUMERY package determines the dependence of the approximation error on the order of the approximating polynomial. A digital temperature error correction method that allows the correction of sensor errors by using TEDS is proposed. The algorithm efficiency in terms of nonlinearity of the temperature error is determined by the accuracy of the fit of the approximating polynomial.Документ Відкритий доступ Дослідження переваг використання інтегральної компоновки для легкого безпілотного літального апарату(КПІ ім. Ігоря Сікорського, 2019) Лапушенко, В. В.; Мариношенко, О. П.Документ Відкритий доступ Автоматизована система регулювання параметрів мікроклімату(КПІ ім. Ігоря Сікорського, 2019) Добролюбова, М. В.; Філіппова, М. В.; Нерозна, І. О.Документ Відкритий доступ Автоматизоване геометричне моделювання дискових робочих органів технічних об’єктів(КПІ ім. Ігоря Сікорського, 2019) Ванін, В. В.; Вірченко, Г. А.; Яблонський, П. М.Документ Відкритий доступ Experimental studies of the algorithms for the temperature measurement time reducing(КПІ ім. Ігоря Сікорського, 2019) Fedorov, V. M.; Savonik, V. O.; Sheyko, Ye. O.; Shtefan, N. I.Скорочення часу під час проведення різноманітних вимірювань є одним із пріоритетних напрямків у метрології. Повною мірою це стосується і рідинних термометрів. Конструктивні методи боротьби із довготривалістю вимірювань за допомогою цього типу термометрів вичерпали себе. На часі – застосування алгоритмічних методів скорочення часу вимірювань. У статті наведені алгоритми обробки показників термометра, які дозволяють по початковій ділянці кривої розігріву знайти значення температури, яка вимірюється.Документ Відкритий доступ Метод розрахунку ресурсу авіаційних конструкцій постобробленням результатів кінцево елементних статичних розрахунків(КПІ ім. Ігоря Сікорського, 2019) Бондаренко, О. М.; Яценко, І. О.Документ Відкритий доступ Solitary Wave Propagation In Elastic Plate On The Winkler Foundation(КПІ ім. Ігоря Сікорського, 2019) Selezov, I. Т.Ми розглядаємо нову задачу, щоб знайти одно-солітонний розв’язок для взаємодії пружної пластини із фундаментом Вінклера. Передбачається, що пластина характеризується пружно-нелінійними властивостями, які описуються геометрично нелінійними деформаціями. У цьому випадку та деякими припущеннями, щоб поздовжні деформації не були враховані, ми отримуємо Лагранжіан, що відповідає класичній моделі Кірхгофа поперечних коливань пластини. Для відповідного розв’язувального рівняння знайдено розв’язок у класі амплітудно модульованих сигналів. За допомогою регуляризації формальних асимптотичних розкладів отримано нелінійне рівняння Шредінгера, що визначає амплітуду у першому порядку малості. Ми отримуємо односолітонний розв’язок відповідно до міркувань та результатів, отриманих Абловіцем та ін., Ньюелом, Захаровим та Шабатом. Існує багато систем широкого застосування у різних галузях, які можуть включати такі елементи. У зв’язку із цим наша стаття розглядає проблему взаємодії пружної пластини із фундаментом Вінклера. Лінійна проблема була вперше дуже чітко розглянута у курсі С. П. Тимошенко «Міцність матеріалів», т. 1 і т. 2, під час роботи у КПІ. З того часу курса, кращого за цей, не було написано.Документ Відкритий доступ Система автоматичного керування рухом центру мас безпілотного літального апарату(КПІ ім. Ігоря Сікорського, 2019) Збруцький, О. В.; Горбачек, Д. О.Документ Відкритий доступ Вплив технічних параметрів на критичну жорсткість рульового приводу(КПІ ім. Ігоря Сікорського, 2019) Бобко, Д. В.; Вірченко, Г. А.Документ Відкритий доступ Досвід використання ERP-систем у життєвому циклі виготовлення виробу на машинобудівному виробництві /(КПІ ім. Ігоря Сікорського, 2019) Корнійчук, Б. О.; Сухов, В. В.Документ Відкритий доступ Інтегрування систем керування мікрокліматом в автоматизовану систему керування підприємством(КПІ ім. Ігоря Сікорського, 2019) Голінко, І. М.; Галицька, І. Є.Modern automation systems are integrated and they include control subsystems interconnected by functions and levels. The integration method of the automatic control system for industrial complexes of artificial microclimate in automated production management systems is proposed. Developed by the authors algorithms for automated air conditioning control and multifunctional mathematical models of climatic equipment in the class of multidimensional systems are proposed to use at the average level of the integrated automated enterprise management system in the support and decision-making system. This increases the efficiency of the artificial microclimate systems functioning during operating conditions changing. The operational management methods for optimization of the artificial microclimate system and operational management on the adaptation of the artificial microclimate system are considered. As a result of the analysis, multifunctional mathematical and algorithmic support for the control systems integrating by industrial airconditioners into computer-integrated production management systems is proposed. The developed models, methods and algorithms are recommended at the stage of designing, debugging, and operating at the middle level of production operational management. The offered mathematical models, methods and algorithms of airconditioners control have been brought to practical realization. The industrial applications results confirmed the high efficiency of automatic control systems for industrial airconditioners, which are designed on the basis of the application of conceptually integrated systems.Документ Відкритий доступ Analysis of cooling of electric motor by radial fan; realization of the experimental analysis of CFD(КПІ ім. Ігоря Сікорського, 2019) Gurkan, Ortamevzi; Ibrahim Emre, GunduzПоказан аеродинамічний аналіз вентиляторів і їх кожухів різних геометрій. Гарне обдування знижує температуру у двигуні та збільшує термін його служби. Зниження температури на 10 градусів може продовжити термін служби електричної ізоляції двигуна у два рази. Для визначення оптимальної геометрії вентилятора і його кожуха, а також оцінки її ефекту, аналіз проводиться за однакових умовах. Метою цього дослідження є визначення стану проектованого електродвигуна, який не має прототипу. Для кореляції аналізів із натурними експериментами був використаний параметр - швидкість входу повітря. Експериментальні результати можуть бути використані для проектування електродвигунів, а також для оптимізації їх аеродинамічних характеристик.Документ Відкритий доступ Дослідження впливу обледеніння крила на його аеродинамічні характеристики методами обчислювальної аеродинаміки(КПІ ім. Ігоря Сікорського, 2019) Доля, Д. О.; Кривохатько, І. С.Документ Відкритий доступ Некоторые подходы к оценке эффективности космической деятельности(КПІ ім. Ігоря Сікорського, 2019) Камелин, А. Б.; Лукомский, В. Г.One of the most important high-tech domestic industries is definitely space industry, which combines science, high technology, technology, economics, production, management and other components. The activity of this industry includes scientific space exploration, the creation and use of space technology, the use of outer space and the evaluation of such activities effectiveness. Particular attention should be paid to assessing effectiveness as the universal socio-economic category characterizing cause and effect relationships and the cost / outcome relationships. Qualitative and quantitative performance criteria are collapsed into an integrated assessment. The results of the performance evaluation should be used to plan and regulate space activities for public development. Some directions of space activity are considered from the point of view of their efficiency estimation, possible results of space technologies use for priority national problems solving, for example: economic development, conservation and development of scientific and technical potential, environmental issues. Possible approaches for effectiveness evaluation of the space projects implementation are presented. In order to evaluate such efficiency, it is important to consider the following points: - the purpose of the work is the main content of the work (formulation of the main tasks of the research, expected results and technical characteristics of the created devices, materials, etc.) and implementation possibilities evaluation; - presence of a backlog (results of previous research and development), level of continuity; - work distribution into stages; - scientific, technical and commercial value of the results of work; - stages of development (scientific program, advance project, sketch project, development of design documentation, preparation of production, manufacture, testing, implementation, operation, processing and use of results); - adjusting of technical requirements substantiated due to various reasons (scientific, technical, financial, etc.) and, accordingly, changes of the work performance terms in comparison with previously adopted ones in the schedule; - breach of the obligations by the co-executors; - force majeure and a number of other provisions.